How To Make A Kaleidoscope What is a Kaleidoscope, Principle, Procedure To Make Kaleidoscope, Know its Uses and FAQs

Table of Content

• Step 1: Choose Your Version--V1: Expensive-and-easy, or V2: Inexpensive-but-a-bit-tricker-to-make
• What you’ll need to make this Homemade Kaleidoscope
• Trending Articles
kaleidoscope At Home With Mirror
• How To Make A Kaleidoscope With Aluminum Foil
• How To Make A Kaleidoscope At Home
• Step 4: For V2 Only: Laminating the Mirror

Just coat the very tip of your kaleidoscope in glue and place it in the crease, rotating it around until it's fully coated. You can toilet paper rolls or 1 empty paper towel roll cut into half. Finally, use the scissors to cut along the lines that you have drawn. When you are finished, you should have two long strips of aluminum foil with a triangle shape in the center.

Never attempt to operate machinery you don't know how to use. Do not look at bright lights with the kaleidoscope, especially a blazing sun, you could damage your eyes. You can replace the rubber band with some sticky tape, if you like.

Step 1: Choose Your Version--V1: Expensive-and-easy, or V2: Inexpensive-but-a-bit-tricker-to-make

If the mirror edges were straight it would save the cost of the laser cutter and more people might try giving it a go, with junk shop mirrors. Experiment with coloring the fundamental domains to emphasize certain symmetries or to create interesting patterns. And don't limit yourself to using only the provided domains. Create different shapes and test them in the kaleidoscope.

Slide the plastic triangle into the paper towel roll. To create your peephole, turn the paper towel tube on one end, standing straight up. Trace a circle around it on black construction or contact paper.

What you’ll need to make this Homemade Kaleidoscope

Glue a petri dish to one end of the PVC tube. The petri dish should be 60 mm by 15 mm and should be made out of plastic. Use PVC cement to attach the petri dish to the tube, being careful not to get any cement on the dish. Cut a piece of foil a little larger than the cardboard and secure it on the card board with clear tape, but only one one end. Step 2 – Next, fill the shot glass or condiment cup about ½ to ¾ of the way with beads.

In addition, placing random shapes into a PK can result in the creation of very interesting and beautiful forms. As of this writing, nobody on the planet produces and sells PKs, so you have to make your own. A kaleidoscope is an optical instrument consisting of two or more reflecting surfaces. These surfaces are tilted towards each other at a certain angle to obtain symmetrical patterns when viewed from the other end. The tube with reflecting surfaces consists of coloured pieces of glass.

Trending Articles

If you have limited access to a laser cutter, you might find it more efficient to cut the fundamental domains at the same time as the mirrors and the handle mounts. To begin, slide your triangular mirror inside the cardboard tube. Take lens 1 and place it inside your tube against the edges of the mirror, notches facing up; this should form a sort of makeshift pouch.

To complete your kaleidoscope, simply roll up the strips of foil around the straw and tape them in place. First, cut a piece of aluminum foil that is about 3 inches by 6 inches. Next, use the scissors to cut out a triangle shape from the folded edge of the foil. Now, unfold the foil and tape the triangle shape to the center of one long side of the foil. Make your own reflective prism by folding a piece of cardboard about 4 x 5 inches into a triangle and sealing off the ends with tape. The foil is cut slightly larger than the cardboard and taped to the card board with clear tape at the only point.

But you can also use construction paper or even gift wrap to jazz it up. And then add on some glitter or stickers if the urge strikes! If there's some tape exposed where you secured your lens, cover it in glitter! It's easy and mess-free if you pour your glitter in the crease of a folded piece of paper.

It amounts to buying an expensive kit with all the parts cut out for you, which you must then assemble, piece by piece. Like an IKEA loft bed, only more precise and you have to cut the pieces yourself. Using the newly formed ring, trace two circles on the plastic sheet. Attach one circle to the ring using clear tape. Trim the remaining circle to be slightly smaller than the ring so it will fit inside. Gather the three mirrors, long sides together and gently fold them into a triangle with the shiny sides facing in.

How To Make A Kaleidoscope With Aluminum Foil

This will be the main tube for the kaleidoscope. Lay the 3 strips side by side and upside down. Be sure to leave a small gap between each strip. "Small gap" here means about 1/8" (.3 cm). Then, tape the mirrors together , bend them into a triangle shape, and set aside. Do not cut completely through the plastic, however.

If you have never used a laser cutter before, I encourage you to find a maker space and learn how to use this easy-to-use and handy machine. This Instructable describes how to easily make three different PKs. They have been designed to be easy to build, and don't require the use of any special tools, except a laser cutter.

Maybe for a classroom if you know someone who will give you a discount on the mirrors. I think your definition of easy somewhat varies from that of the general public as well. And even if it is easy compared to other instructions, it’s still fussy and labor intensive and the cost is extremely prohibitive.

Once you have cut the domains, you can fold them by simply following the score lines. It's a good idea to individually crease each fold completely in order to overcome the bending resistance of the paper. For the simpler domains, there is no need to tape them; they will naturally settle into the proper form when placed in the kaleidoscope. For the more complex domains, you will need to tape parts of them in order to help maintain their shape. For this step, you will need to use a laser cutter or find an online laser cutting service (search "laser cutting service" on Google to find services nearby).

How To Make A Kaleidoscope At Home

This is an easy tutorial on how to make a Kaleidoscope. Hi friends,In this video I will show you how to make a kaleidoscope very easily at home without using mirrors.It is very easy to make and can be made just in... Put bright and shiny beads inside your kaleidoscope, don't use dull colors.

I think I used an organic or "green" paint remover, which resulted in the reflective coating being visible on both sides. The rear surface became the front surface and worked great. The easiest way to make this kaleidoscope look as impressive as possible is contact paper -- so long as you work out the bubbles!